J-47487 Idler 3 Cantilever Tool for Detroit DD13 DD15 Engine Diesel Gear Train
Specifications
| Return Shipping Will Be Paid By | Seller |
| Returns Accepted | Returns Accepted |
| Item Must Be Returned Within | 60 Days |
| Brand | Unbranded |
| Type | Idler 3 Cantilever Too |
| Manufacturer Part Number | Does Not Apply |
| Warranty | 1 Year |
J-47487 Idler 3 Cantilever Tool for Detroit DD13 DD15 Engine Diesel Gear TrainApplications – Fits for all Detroit Diesel DD13 and Detroit Diesel DD15 commonly found on Freightliner Cascadia trucks.Function -- Used with the DDC procedure to set the gear timing for cam installation. Makes installation and timing of engine gear train with ease.Easy to Use -- Simply install our J-47487cantilever tool onto idler gear No. 3 and install two bolts into the spindle and idler gear No. 3, then snug the bolts.Nice Performance – Made from high quality carbon steel for corrosion, rust and impact resistant. Alternative to J-47487.100% Satisfaction Guarantee -- If you're not 100% satisfied with this tool, simply return it for a full refund in 60 days. Premium Support & 12-Month Warranty. Upgrade Design Used with the DDC procedure to set the gear timing for cam installation Provides the most effective mechanical advantage for easy operation Superior QualityPremium grade heavy duty soild steel structure with black oxide finishedSuperior durability and strengthAnti-corrosion and anti-rustAnti-impact and anti-deformationSpecial FeaturesManufactured to OEM specificationsThe greatest replacement for OEM Part J-47487High precision and toughness to provide a much longer service lifeNOTE: Coat the inside of the gears, bushings and gear train with clean oil before installation.Install the crankshaft gear on the crankshaft.Rotate the crankshaft to Top Dead Center (TDC) on cylinder No. 1. Install and lock crankshaft TDC locating tool into place with bolt.Install spindle into idler gear No. 5.Install idler gear No. 5 onto the cylinder head using shoulder bolt.Install two bolts into idler gear No. 5 and hand tighten. Remove the shoulder bolt. Torque to 60-65 N·m (44-48 lb·ft).Install the spindle into idler gear No. 3.Install the cantilever tool (J-47487) onto idler gear No. 3.Install two bolts into the spindle and idler gear No. 3; snug the bolts.Remove the cantilever tool (J-47487) from idler gear No. 3. NOTE: When idler gear No. 3 and cantilever for idler No. 3 tool are installed to the gear case, cantilever for idler No. 3 tool should come off of the gear with ease. If the timing tool is not easily removed, that is an indication that the gears are not timed. Check the gear lash between idler gear No. 3 and idler gear No. 5.Install a dial indicator onto gear case and position the stem to rest between the teeth on large gear of idler gear No. 3; zero out the dial indicator.Hold idler gear No. 5 with a screwdriver to check gear lash.The lash reading on the dial indicator should be 0.079 - 0.305 mm (0.003-0.012 in.).When correct gear lash is established, torque idler gear No. 3 to 60–65 N·m (44-48 lb·ft).Install the cantilever tool (J-47487) onto idler gear No. 3.Install the spindle and gear plate onto the idler gear No. 2.Install the spindle, idler gear No. 2, and the gear plate onto the cylinder block. Torque to 100 N·m (73 lb·ft).Remove the air compressor to the cylinder block (if installed). Refer to section "Removal of the Air Compressor".Install the thrust washers and spindle onto the idler gear No. 1.NOTE: For ease of installation on idler gear No. 1, roll the gear into idler gear No. 2.Install the spindle, thrust washers, idler gear No. 1, and gear plate onto the cylinder block by engaging the teeth of idler gear No. 1 into the crankshaft gear teeth first, then roll upward into idler gear No. 2. Torque to 100 N·m (73 lb·ft).Install the air compressor. Refer to section "Installation of the Air Compressor".NOTE: When installing idler gear No. 4, verify that the part number on the gear is facing the block.On the DD15 and DD16, with the cone of the idler gear No. 4 facing outward, install the thrust washer onto the spindle then install the spindle onto the idler gear No. 4.On the DD15 and DD16, install the assembled thrust washer, spindle and idler gear No. 4 onto the cylinder block. Torque to 100 N·m (73 lb·ft).NOTE: Tool J-47487 should remove with ease. If not, check gears for proper installation.Remove the cantilever tool (J-47487) for idler No. 3.PaymentShippingReturnsContact usPayment 1. Payment methods accepted: Payoneer. Our Payoneer account allows you to pay by credit card, debit card and your paypal balance. 2. All major credit cards are accepted through our secure payment processor Payoneer. 3. We ship items to Your Ebay address.Please make sure your Ebay address is correct before you pay, cause it cannot be changed once the order shipped out.Shipping 1. Item will be shipped out within 1-2 business day after clear payment received. 2. Please make sure shipping address on your Ebay account is correct & up-to-date. 3. All of our items are shipped from our US warehouse. 4. Please feel free to contact us by email if you cannot get your order in time. Please read the shipment and payment detail carefully before you bid.Returns 1. Return to us within 60 days from the delivery date for exchange or refund. Refund will be given as Money back or item exchange (buyer's choice). 2. Return shipping fee is the responsibility of buyer unless the return is a result of our mistake. 3. If you need return, please contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation.Contact us Please contact us via ebay using"Contact member". We will respond within 1 business day or less.Thank you for your understanding.
